A dripping tap usually points to a faulty valve or seal, not a need to replace the whole fitting. How to fix a dripping tap depends on its type: a compression tap may need a new rubber washer, while a ceramic disc valve may need cleaning or replacing. First, turn off the water supply and open the tap to drain excess water from the pipes.
A steady drip is frustrating, especially when it returns after you tighten the handle. Identify the valve before taking the tap apart so you can focus on the likely cause and avoid damaging its parts.
This guide explains how to recognise ceramic disc and compression taps, prepare safely for the repair, and clean or replace the relevant valve parts. You’ll also learn what a leak from the spout or beneath the handle can indicate, and when wear or corrosion may make a repair less suitable.
Key Takeaways
- Identify the valve before choosing a repair: ceramic disc taps usually turn half a turn or less, while compression taps use rubber washers and need a full turn or more.
- A drip from the spout often points to a worn washer or dirty or scratched ceramic discs. A leak beneath the handle can indicate a damaged O-ring.
- Before dismantling a tap, shut off the supply at the isolation valve or main stopcock, run off excess water and plug the sink to catch small parts.
- Clean or replace worn parts carefully, and avoid overtightening. Corrosion, worn threads or recurring leaks can mean repair is only temporary.
What causes taps to drip?
Call a plumber if the tap is corroded, its threads are worn, or it still leaks after a repair. In these cases, dismantling or tightening the tap may not solve the problem.
In the UK, repair cost depends on the fault, parts required and access, and is given after a quote request.
- Locate the leak. Dry the tap and watch where water appears. A drip from the spout usually points to a worn sealing part inside the valve. Water beneath the handle suggests a valve O-ring needs replacing.
- Check how the handle turns. Modern ceramic disc valve taps typically reach maximum power after half a turn or less. Scratched or dirty ceramic discs can stop the valve sealing properly, allowing water to escape from the spout.
- Look for a compression valve. These taps typically need a full turn or more to reach maximum power. They use rubber washers, unlike ceramic disc taps, so the repair depends on identifying which valve is fitted.
- Consider washer wear. In a UK compression tap, the rubber washer sits at the base of the valve and seals against water flow. As it wears away, water can pass the seal and drip from the spout.
- Notice leaks around the handle. Water appearing beneath the handle has a different likely cause from a spout drip. Replacing the valve O-ring is the recommended repair for this leak location.
- Assess the tap’s condition before choosing how to fix a dripping tap. An old or corroded tap, or one with worn threads, may only improve temporarily after repair. Replacement can be more suitable when damage affects the tap body or its fittings.
Cleaning or replacing a ceramic disc valve
Identify the tap before removing any parts. Ceramic disc valves usually reach full flow after half a turn or less, while compression taps typically need a full turn or more. The handle’s movement can help you tell them apart.
-
Identify the tap type
Turn the handle gently and note how far it moves before water reaches full flow. A ceramic disc tap generally needs half a turn or less; a compression tap usually needs a full turn or more. Check whether it has separate hot and cold handles or one mixer handle, but don’t rely on appearance alone. If the handle feels stiff, don’t force it, as this can damage the fitting.
-
Clean a ceramic disc valve
Remove the handle and valve assembly carefully, keeping small parts together in order. Check the ceramic discs for dirt, deposits or scratches, which can prevent a proper seal. Rinse away loose debris and gently wipe accessible surfaces with a soft cloth. Avoid abrasive tools, as they can scratch the discs. Reassemble the parts in their original order, then turn the handle gently to test the flow.
-
Replace a ceramic disc valve
Replace the valve assembly if its discs are scratched or cleaning hasn’t stopped the drip. Match the replacement to the original valve’s shape and fittings, not just its appearance. Lift out the old assembly without levering against the tap body, then seat the replacement squarely. Tighten the retaining parts securely without overtightening. Restore the water supply gradually and check the spout and handle for leaks.
If the valve is stuck, damaged or still leaking after fitting, get help with tap repairs.

Compression valve taps and rubber washers
Compression taps use a rubber washer to close the waterway. Follow these steps to inspect and replace the washer if water drips from the spout.
- Confirm the tap uses a compression valve. Turn the handle and observe how far it moves before water reaches full flow. UK compression taps typically need a full turn or more and use rubber washers. This helps distinguish them from ceramic disc taps, which generally need less handle movement.
- Remove the valve and locate the washer. Once the water supply is isolated, take off the handle and unscrew the valve carefully. Keep the parts in order as you remove them. The rubber washer sits at the base of the valve, where it seals against water flow.
- Inspect the washer and valve seat. Look for a washer that appears worn, flattened, split or uneven. Check the valve seat, where the washer presses closed, for debris or visible damage. A worn washer can leave a gap, allowing water to pass through and drip from the spout.
- Replace a worn washer with a matching part. Remove the old washer and compare it with the replacement before fitting. The new washer needs to sit flat at the valve base, without twisting or catching. A poor fit can prevent the seal from closing properly, so check its position before reassembling the tap.
- Reassemble and test the tap gently. Return the valve and handle to their original positions, then restore the water supply. Turn the handle to close the tap and watch the spout for further drips. Tighten parts only enough to secure them. Overtightening can stress components and lead to leaks.
If a new washer doesn’t stop the spout dripping, inspect the valve seat again. Damage or persistent leakage may mean the washer isn’t the only cause.
Preparing for tap repairs
The main risk during tap repairs is water escaping while the valve is open. Turn off the supply before dismantling anything, and plug the sink so small parts can’t fall down the drain.
- Find the correct shut-off point. Look for the isolation valve under the sink and turn off the water there. If there isn’t an accessible isolation valve, use the main stopcock. Make sure you know which tap the control affects before starting work.
- Run the tap to clear the pipework. After shutting off the supply, open the tap and let excess water run out. This reduces water left in the pipes when you remove the handle or valve. Keep a cloth nearby to catch drips from the fitting.
- Identify the hot and cold valves. Check the bottom seals: the hot-water valve has a red seal, and the cold-water valve has a blue seal. If you’re repairing one side, note its position before removal. This helps you return each valve to the correct place.
- Protect the plughole. Fit the sink plug before loosening screws or lifting out small components. A handle screw or washer can slip from your fingers and disappear down the drain. Keep removed parts together on a clear surface, in the order you take them off.
- Prepare the work area. Clear bottles, soap and other items from around the tap and sink. Put a cloth beside the fitting, then arrange the removed parts where they won’t be knocked onto the floor. A clear space makes it easier to see how components fit together.
- Stop if the supply won’t shut off. Don’t dismantle the tap while water continues flowing. Check that you’ve turned the correct isolation valve or stopcock. If you can’t stop the supply or control water escaping, get help with tap repairs.
RPH Plumbing: Plumbing Services
RPH Plumbing repairs tap leaks that need further diagnosis or attention. If a new washer hasn’t stopped the drip or the valve is difficult to remove, a plumber can help prevent further damage to the fitting. Plumbing help is also useful when corrosion or worn threads make a simple repair unsuitable, or when water continues to leak after reassembly.
Before arranging a repair, note whether water comes from the spout or beneath the handle, and whether the tap has a ceramic disc valve or compression washer. These details help explain what you’ve checked and where the leak appears. If the tap remains troublesome after basic checks, contact RPH Plumbing to discuss the repair.
Make the next repair decision with confidence
Knowing how to fix a dripping tap can help you make an informed decision. After a repair, watch for moisture around the fitting as well as drops from the spout, and note whether the leak returns when you open and close the tap. This clear account can help distinguish a lasting repair from a fault that needs further attention. A brief note of any changes can prevent guesswork later.
If the tap still leaks, parts feel seized, or you’re unsure about dismantling it, don’t force the fitting. Damage can turn a small repair into a more involved problem. Discuss the issue and any work already attempted with RPH Plumbing, then decide how to proceed with clear information.
Contact RPH Plumbing for help and take the next step towards a properly working tap.
Frequently Asked Questions
How can I prevent a tap from dripping?
Move the handle smoothly and don’t force it past its natural stopping point. If it becomes loose or stiff, or starts making an unusual noise, investigate before the problem worsens. Keep the tap’s exterior clean so you can spot fresh moisture around the base. A quick visual check after cleaning the sink can help you notice changes early.
How do I turn off the water supply to my tap?
Find the control on the pipe feeding the tap rather than turning an unrelated valve. Tracing the pipework can help distinguish a local control from the main stopcock. If the pipe disappears behind a cupboard or panel, clear the area and use a torch to see the fittings. Don’t turn controls at random, especially if their purpose is unclear.
What tools and materials are needed to fix a dripping tap?
Gather a screwdriver and adjustable spanner, along with a cloth and a small container for removed parts. You’ll also need the correct washer or valve component for your tap. A clear photograph of the handle and fitting can help identify the make or model when choosing a replacement. Keep the parts together so you don’t lose small screws.
How do you turn off the water supply before repairing a tap?
Use the control that feeds the tap you intend to repair, and make sure you can identify it before starting. A local valve isolates that tap, while the main stopcock controls the property’s water supply. If the pipework is concealed, inspect it carefully rather than guessing. Keep the control accessible in case you need to stop the supply again.
How do you replace a washer in a traditional compression tap?
Replace the washer on the leaking side rather than dismantling both handles without a reason. If the tap has separate hot and cold controls, note which handle is affected before taking it apart. Choose a washer that sits securely in the valve without obstructing its movement. After reassembly, check that the handle turns freely and closes without excessive force.
How do you repair a dripping ceramic disc or quarter-turn tap?
For a quarter-turn tap, check the make and model before sourcing a replacement valve. Similar-looking cartridges can differ in stem shape or fitting arrangement, so appearance alone may not identify the right part. If the tap leaks around the handle rather than the spout, a different seal may be at fault. Match the repair to the leak’s location.
